West London borough with high-value period conversions where quality finishing work — tiling, plastering, decorating — matters most. Hammersmith and Fulham falls well within the West London ground Lian Construction covers on a regular basis. For external rendering and facade repair work in Hammersmith and Fulham, that local knowledge means fewer surprises once work is on site and a team that already understands the borough's typical property stock.
Hammersmith and Fulham's housing stock is dominated by the kind of period property found across much of inner and West London: Victorian and Edwardian terraces and villas, many of which have been split into flats over the decades, alongside mansion blocks and some purpose-built conversions from the early to mid-20th century. A significant share of the borough's homes are conversions rather than single-family houses, which is typical of high-value West London areas where large period houses have been reworked into two, three or more flats to meet demand. This conversion history means a lot of the existing stock carries older wall and floor build-ups, original plasterwork in varying condition, and layouts that have been altered more than once. As with other West London boroughs, there's also a mix of ex-local authority blocks and post-war infill alongside the period stock. Because so much of the housing is period conversion rather than new-build, quality of finish tends to matter more here than in areas with a higher proportion of modern construction, since old walls, ceilings and floors need careful preparation before tiling, plastering or decorating will look right and last.
In a borough where so much of the property is high-value period conversion, the finishing trades carry more weight than they might elsewhere. A flat carved out of a Victorian terrace lives or dies on how well the plaster, tiling and decorating are done, since buyers and tenants at this end of the market notice uneven walls, poor tile lines or rough paintwork more readily than they would in a standard new-build. That creates steady demand for contractors who can do finishing work properly rather than just quickly, particularly on bathroom and kitchen refits where tiling quality is hard to hide. It also means homeowners and landlords doing up a conversion flat are often better served focusing budget on getting the finishing right rather than cutting corners to save on the last stage of a project. For landlords specifically, a well-finished conversion tends to let faster and at a better rent in this kind of market, so the extra cost of proper plastering and tiling work is usually recovered over time. Given the age and variability of the underlying building fabric, it's also worth budgeting some contingency for making good old walls and floors before the visible finishing work even starts.
Given how much of Hammersmith and Fulham's housing stock is period conversion, it's worth being aware that conservation area and listed building rules are common across this type of West London property, as they are in many inner London boroughs. Converting or altering a period house can trigger planning or listed building consent requirements depending on the specific property and area, particularly for external changes, window replacements or work affecting original features. Internal finishing work like plastering, tiling and decorating is generally more straightforward from a planning perspective, but if it's part of a wider conversion or alteration project it's sensible to check the property's status with the council before starting. As with any older building, it's also worth confirming what internal fabric might be original or protected before stripping back walls, since this can affect both the approach and the cost of the finishing work.
Render and damp on Victorian solid-wall properties
A large proportion of the render repair we're called out for on Victorian and Edwardian houses traces back to the same underlying issue: a hard cement render applied to a solid brick wall that was never designed to be sealed in that way. Solid walls, common in London terraces built before cavity construction became standard in the 1920s and 30s, rely on being able to absorb and release moisture through the wall itself. A modern cement render, particularly one applied at a rich mix ratio with little lime content, is far less permeable than the brick behind it, and once moisture gets in, through a crack, a poorly detailed reveal or rising damp at the base of the wall, it can't easily evaporate back out through the render. Instead it tracks sideways or gets pushed further into the wall, sometimes showing up as damp patches on internal plaster well away from the original point of failure. This is why re-rendering a Victorian solid wall after a damp problem often means specifying a lime-based render, typically an NHL 3.5 or similar hydraulic lime mix, rather than simply replacing like-for-like with the cement render that likely contributed to the problem in the first place. Where we're asked to deal with damp linked to render on a solid wall, we'd typically expect the sequence to run: confirm the wall is genuinely solid rather than an unrecognised cavity, remove the render causing the problem, allow the wall to dry out for a period before re-rendering, and then apply a breathable lime specification rather than rushing straight back to a like-for-like cement finish. Skipping the drying period is a common shortcut that undermines an otherwise correct specification, since re-rendering over a wall that's still saturated just traps the existing moisture behind the new coat rather than solving anything. Lime render isn't a universal fix for every damp issue, and where the underlying cause is a specific defect such as a failed damp proof course or a blocked cavity tray, that needs addressing on its own terms, but on a genuinely solid-wall property, breathability is usually the right starting principle for whatever render goes back on.
Render and External Wall Insulation (EWI)
External Wall Insulation systems, increasingly common on solid-wall Victorian and ex-council properties looking to improve thermal performance, change how the render on a wall needs to be specified and detailed. EWI involves fixing rigid insulation boards to the outside of the wall, then applying a reinforced base coat with mesh embedded into it, followed by a top coat, usually a silicone or acrylic render, rather than rendering directly onto brick. Where we're asked to re-render a wall that already has EWI installed, or to repair render that's failed on an EWI system, the detailing at openings matters more than on a solid masonry wall, since window and door reveals, meter boxes and pipe penetrations all need the insulation and render built up correctly around them to avoid a thermal bridge or a point where water can track behind the system. Reveal depth changes too, since adding insulation and render to an external wall typically adds 80 to 150mm of thickness depending on the insulation used, which affects how windows, door thresholds, cills and rainwater goods need to be extended or re-detailed to sit properly against the new wall face. We don't design or specify EWI insulation systems as a standalone service, but where render work is needed on a wall with EWI already fitted, or as part of a wider EWI installation being coordinated by others, we work to the system manufacturer's detailing requirements so the render performs and weathers as the system was designed to.